Honeywell T8600 & T8500 --Installation Instructions

Honeywell® products
at discounted prices

Air Purification Products

Pleated filters 40% 1 in.
Pleated filters 40% 2 in.
Pleated filters 60% 2 in.
Pleated filters 40% 4 inch
Pleated filters 60% 4 inch
Media filters 4 3/8 inch
Frame & filters 4 3/8 inch
Generic Media
Ultraviolet Lights
Electronic Air Cleaners
EAC Replacement Cells
Prefilters & Postfilters
Airwatch®, Monitors
Ventilation Units
Dampers & Actuators
CO & CO2 Sensors
Smoke Sensors
Portable HEPA Filter

Honeywell® Thermostats

COMPARE --
Programmable.pdf
Non-Programmable.pdf
Non-Digital.pdf
VisionPro™ IAQ Best
VisionPRO© 8000 Best
CommercialPRO™8220 Best
CommercialPRO™7220 Great
FocusPRO™ 6000 Great
FocusPRO™ 5000 Better
PRO™ 4000 Better
PRO™ 3000 Good
PRO™ 2000 *Basic
Low Voltage Accustat®
Honeywell Line Voltage
Line Voltage Accustat®
Digital Round
Non-Digital bi-metal
Electronic Programmable
Heat Pump
Flush Mount
Non-Programmable
Sale Models
PC8900 Perfect Climate
Outdoor Sensors A or B
Telephone Access
Remote Room Sensors
Communicating Tstat
Networked Zoning
Honeywell® MiniZone®
Zoning Catalog.pdf

Humidifiers

Bypass Disk
Bypass Flow Through
Power Flow Through
Steam Power
Controls & Components
Skuttle® Parts
Honeywell® Parts

Unit Heaters

Reznor® Garage Heating
Separated Combustion
Standing Pilot
Oil Fired
Hydronic
Indoor Heaters
Outdoor Heaters
UpFlow Indoor
Infrared Heaters
Empire® Gas Heaters

James A/C Co.

serving Do-It-Yourselfers since 1990.
Satisfying every customer....one at a time!

EDUCATE ME

Click to verify BBB accreditation and to see a BBB report.

Call toll free 1-866-584-0355 or 1-903-759-2160
309 Patriot Circle, Longview, TX 75604-2240

For now you can write down the part numbers and E-Mail me your requests. Personal checks are sufficient for payment also. For cards, just e-mail me your telephone number and I will call you for the information. I HAVE NO SECURE SERVER. SEND ME A PHONE NUMBER FOR TRANSACTIONS, PLEASE.

HoneywellChronotherm®IV
Deluxe Programmable Thermostats:

To access Installer Setup Options:
press three keys at once:
(1)the information key, (2)the increase key and (3)the decrease key.

Installer Setup
Choices	Number	(press Time Uparrow key to change)
Fan operation.	2	0=Conventional applications where equipment controls fan operation in heat mode. 1=Heat pump or electric heat applications where thermostat controls fan operation in heat mode.
Heating cycle rate cph=cycles per hour	4	1=1 cph used for radiant floor heat, gravity system 3=3 cph used for hot water systems or high efficiency furnaces 6=6 cph (default) used for conventional heat 9=9 cph used for electric heat systems
System setting adjustment	12	0=Auto changeover 1=Manual changeover (default) 2=Fixed auto changeover
Adaptive Intelligent Recovery (trademark) control	13	0=Adaptive Intelligent Recovery control is activated (system starts early so setpoint is reached by start of program period) 1=Conventional recovery (system starts recovery at programmed time)
Degree temperature display	14	0=Temperature is displayed in °F 1=Temperature is displayed in °C
Clock format	16	12-hour clock format 24-hour clock format
Extended fan operation in heating*	19	0=No extended fan operation after the call for heat ends 1=Fan operation is extended 90 seconds after the call for heat ends
Extended fan operation in cooling*	20	0=No extended fan operation after the call for cool ends 1=Fan operation is extended 90 seconds after the call for cool ends.
Outdoor temperature display (select models)	24	0=No outdoor temperature is displayed 1=Outdoor temperature is displayed. Needs a C7089B1000 Outdoor Sensor to operate
Deadband	30	Heating and cooling setpoints can be set no closer than the chosen value: 2=2°F (1°C) apart 3=3°F (1.5°C) apart (default) 4=4°F (2°C) apart 5=5°F (2.5°C) apart 6=6°F (3°C) apart 7=7°F (3.5°C) apart 8=8°F (4°C) apart 9=9°F (4.5°C) apart 10=10°F (5°C) apart
Minimum off time for the compressor	33	0 thur 5=Minimum number of minutes (0 thru 5) the compressor will be off between calls for the compressor (5 is the default).
Temperature range stops in heating	34	40 to 90=Temperature range (1°F increments) heating setpoint can be set to (90 is the default)
Temperature range stops in cooling	35	45 to 99=Temperature range (1°F increments) cooling setpoint can be set to (45 is the default).
Temperature display adjustment	37	0=No difference in displayed temperature and actual room temperature (default) 1=Display adjusts to 1°F higher than actual room temperature 2=Display adjusts to 2°F higher than actual room temperature 3=Display adjusts to 3°F higher than actual room temperature 4=Display adjusts to 1°F lower than actual room temperature 5=Display adjusts to 2°F lower than actual room temperature 6=Display adjusts to 3°F lower than actual room temperature

* Number 2 must also be set to 1 to extend fan operation.

If you have comments or suggestions, please email me at James' A/C Co.